Skip to main content

v5.0

by Q-See

Introduction

Q-SEE PLUS IS ONLY COMPATIBLE WITH WI-FI ENABLED QCW IP CAMERAS.

  1. Select the Add Device icon.
    • Select the Add Device icon.

    • If you already have a device added, select the + in the top right corner.

    • PLEASE BE SURE THAT THE LED ON THE CAMERA IS BLINKING GREEN. IF NOT, PRESS AND HOLD THE RESET BUTTON FOR 15 SECONDS AND TRY AGAIN.

  2. Scan the QR Code on your camera.
    • Scan the QR Code on your camera.

    • If you are having difficulty scanning the QR code try using the Flash on your phone.

  3. Select Your Camera
    • Select Your Camera

  4. Ensure your device is powered on.
    • Ensure your device is powered on.

    • Select Next

  5. Your phone must be connected to the Wi-Fi network you wish to connect your camera to.
    • Your phone must be connected to the Wi-Fi network you wish to connect your camera to.

    • Enter the Password to your Wi-Fi network.

    • Select Next

  6. Check the status indicator on your camera.
    • Check the status indicator on your camera.

    • Check the box The light is steady flashing green

    • Select Next

  7. Your phone will make a cuckoo cuckoo noise as it tries to sync with your camera.
    • Your phone will make a cuckoo cuckoo noise as it tries to sync with your camera.

    • Select Next

  8. While Q-See Plus configures your camera, your mobile device may begin to make a chime noise, this is normal and you can lower the volume if you wish.
    • While Q-See Plus configures your camera, your mobile device may begin to make a chime noise, this is normal and you can lower the volume if you wish.

    • Q-See Plus will configure the network.

    • Please be patient, this process may take up to 3 minutes depending on the network speed. If the configuration fails, please ensure your phone and Wi-Fi camera are in range of the Wi-Fi signal.

    • IF you are experiencing issues connecting to a Wi-Fi network, (CLICK HERE) for Wi-Fi Connectivity Troubleshooting

  9. Set a New Password for your camera
    • Set a New Password for your camera

    • Password must be between 8 - 32 characters.

    • Select Next

  10. Verify your Time Zone to ensure accurate time.
    • Verify your Time Zone to ensure accurate time.

    • Select Start Preview

  11. Q-See Plus will begin to show the live feed from your camera.
    • Q-See Plus will begin to show the live feed from your camera.

    • Motion Detection and Push Notifications are enabled by default.

    • Select the Camera icon to take a Snap Shot of the live feed.

    • Select the Microphone icon to begin 2-Way Talk, tap again to stop.

    • Select the Camcorder icon to start recording the live feed, tap again to stop.

    • If your camera is PT (Pan-Tilt) or PTZ (Pan-Tilt-Zoom) enabled, Select the PTZ icon to access the controls.

  12. Select the Gear icon in the top right corner to go to the device's settings.
    • Select the Gear icon in the top right corner to go to the device's settings.

    • Select the Display icon to alternate between single and 4 channel view.

    • Select the Quality icon to alternate between Standard and High Definition.

    • The Standard Definition feed is shown by default to limit bandwidth use but the High Definition image is still recorded.

    • Select the Speaker icon to begin listening to the audio from the camera, tap again to stop.

    • Select the Full-Screen icon to manually enter full-screen mode. Alternatively, you can rotate your device to enter full-screen mode.

Finish Line

4 other people completed this guide.

Q-See

Member since: 09/21/2017

15,626 Reputation

94 Guides authored

One Comment

Great Info. Thank you.

Bill Nguyen - Reply

Add Comment

View Statistics:

Past 24 Hours: 22

Past 7 Days: 96

Past 30 Days: 545

All Time: 6,141